How To Install A Caseta Wireless 3 Way Switch

Lutron Caseta Wireless in Wall Dimmer & Switch Installation

Ready to install your Lutron Caseta Wireless in Wall Dimmer and/or switch? Read along and learn to wire single, three way, and 4 fashion Lutron Caseta Smart switches and how to install Pico Remotes.

Trying to wire a Ra2 Select switch? Wire Your Ra2 Select Switch Here!

FOR Informational PURPOSES ONLY – Please refer to terms of use bellow.

Want To Encounter ALL The Caseta Wireless Devices, Even Ones Not Advertised?

Thats right.. Observe all the products available at:

Want
To See ALL The Caseta Wireless Devices, Even Ones Not Advertised?

Thats right.. Find all the products bachelor: at

Tools Needed To Wire Smart Switch

Philips Screwdriver
Flat Head Screwdriver
Wire Strippers
Volt Meter or Induction Tester (be safe)
Level (arrive look neat)

Plan Of Activeness

First, you need to determine where you desire to install your new Lutron Caseta Wireless device/s. Second, yous need to brand certain the switch you are removing is not a 3 manner (2 switches to control aforementioned low-cal) or you will need a Pico Remote and want a Wall Mounting Plate for the second location.

This is because if you have a iii way, your one-time existing switch will non work with the Lutron Caseta devices. Lastly, make sure your load (lights, fan, fountain pump) can be dimmed or yous will need a switch not a dimmer.

Prophylactic First

Offset, you lot demand to shut off the breaker for the circuit your working on!

I recommend turning on the light first and look for information technology to shut off when you lot plow off the billow. One time the old switch is pulled away from the wall, It's always a good idea to take an consecration tester and brand sure all the wires that your working effectually are turned off. Considering there may be another circuit in the switch box that are still hot!

Installing Lutron Caseta Wireless in Wall Dimmer or Switch

Non-Neutral Based Caseta Switch - Unmarried

For Lutrons Diagram Click Here!

LUT-MUT Resistor comes with not-neutral switches and is merely needed for certain loads. Try installing the resistor the fashion shown if switch is blinking red and not working.

Installation Of Switch

1st)

Pull out old switch – Become ahead and remove the ii screws on the cover plate and pop it off. After that you tin can remove the two screws holding the old switch in identify and then carefully pull information technology out.

Now you can check with the consecration tester to verify indeed everything in that switch box is off.

old dimmer being removed

Pull out erstwhile switch – Go ahead and remove the two screws on the cover plate and pop it off. Afterwards that you tin can remove the two screws holding the old switch in place and so advisedly pull it out.

Now you lot can check with the consecration tester to verify indeed everything in that switch box is off.

2nd)

Once safe, go ahead and remove device and wires. Occasionaly y'all may need to slightly cut dorsum and re-strip the wires if the copper or insolation is to damaged.

You should accept 3 wires on the dimmer, a Line (power), a switch leg (load or appliance), and a basis. Switch volition have a blue wire that can exist capped off with the blue wire nut they supply.

Brand certain to ground your switch.

Caseta switch showing the wiring

As I've shown, It will not thing which way you claw up the black wires on the dimmer or switch.

The non-neutral switch comes with a resistor that is recommended to be used when wiring for LED, CFL, ELV loads.

Refer to diagram- the resistor will wire from switched hot wire to the neutral wire.

3rd)

Now become ahead and carefully constrict your wire back into the box and install your new switch with the new screws provided.

Reattach your encompass plate and level information technology. Turn on ability and test it out.

installing Caseta Wireless switch

Now become ahead and carefully tuck your wire dorsum into the box and install your new switch with the new screws provided.

Reattach your cover plate and level it. Plough on power and examination information technology out.

4th)

Start setting up the Lutron Caseta span or if that's already done become into the programming the wall dimmers and devices.

installing caseta bridge

Install Your Pico Remote With Wall Plate

1st)

Pause off the tab as shown. The wall plate has the directions on it every bit well.

Pico Remote Wall Plate

Break off the tab as shown. The wall plate has the directions on it as well.

2nd)

Slip Pico Remote onto the wall plate tab.

pico remote mounted on wall plate

third)

Attach the wall mounting plate to the wall or over old existing switch box location.

Do this with 2 screws as shown.

Mounting Pico Remote in a Remote location

Attach the wall mounting plate to the wall or over old existing switch box location.

Practice this with 2 screws equally shown.

fourth)

Now screw the switch encompass plate to the Pico Remote Wall Mounting Plate.

Lastly, Snap on your the screw less cover plate if using Lutrons faceplate and you'r all set to go.

Install screw less plate onto Pico Remote

Wall mounted Pico Remote

For Neutral Based Switches

The neutral based switches are a little different. And then now you demand to hook the switch upward to a neutral wire (white wire). Before ordering/installing make sure you have a neutral in the electric box that y'all programme on wiring the switch.

Also these switches demand you to claw the wire up to screw terminals and it DOES thing which fashion you hook up ability (polarity).

Black Screw = Line In/ Constant Power
Silver/White Screw = Neutral
Brass Screw = Power out/ Switch Leg to Load

Other than this yous tin can become ahead and follow the aforementionedInstallation Of Switch

Neutral Based Caseta Switch - Single

Wire Lutron Caseta Wireless iii Style Switch

This is when we have 2 switches that are decision-making the same group of lights.

***FYI, Pico Remote can exist installed in either location. I advise putting it at the 3 way switch location where y'all may prefer to use the scene retentiveness feature and control multiple of calorie-free zones.***

1st Lutron Caseta Wireless iii way Switch Location

1st) Remove the old device.

2nd) You volition need to Identify the wires. I want to explain what wires your Virtually LIKELY (y'all must verify) looking at.

Romex / Conduit 1 – Yous will have line in or load out (refer to diagrams below), most likely a neutral, and basis. So if in Romex, that Romex would take black(Line in or Load out), white(Neutral), and a bare copper(Ground).

Romex / Conduit 2- You volition then have 2 traveler wires and nearly likely the neutral and basis. And then if the traveler wires are in Romex, that Romex would take a black(Traveler one), scarlet(Traveler ii), white(Neutral), and a bare copper(Ground).

3rd) We need to separate the travelers. And then await upwardly in there and see which ii wires (almost probable a ruby-red and black) travel downwardly the aforementioned romex or conduit together. Refer to the diagram below to aid identify your wiring.

4th) Choose 1 traveler to wire the switch leg (Load/Light) and rubber off the extra traveler wire. For instance in my example, I connect Caseta Switch to blackness wire and safe off the cherry.

5th) At present install your new switch and cover plate with screws provided. So Proceed to removing your other switch at the 2nd location, explained below.

Non-Neutral Caseta Switch Wiring - three Way

Neutral Based Caseta Switch Wiring - 3 Mode

second Lutron Caseta Wireless three Way Switch Location

Remove your old device.
At present look upwards in the electrical box and identify the traveler wires, same equally earlier, and safe off the ane that will not be used. Again, In my example I safe off the red wire.
Take the other traveler (blackness in my instance) and tie it through to power or the load, depends on your which location your Pico Remote is existence installed. (refer to diagram above – In case, Pico is being installed at second location. This switch is closest to the load, so the traveler wire(black) is then wired to the load wire which feeds the light.)
Now carefully shove all the wires in the box and install your wall mounting plate. Follow the instructions on its sticker.
Install your Pico Remote onto the wall mounting plate
Mount the wall mounting plate on the wall.
Install your embrace plate onto the wall mounting plate.
Level it out with your level and you'r all ready.

Wire Lutron Caseta Wireless 4 Manner Switch

In a iv mode application, It wires the same way as a three style. The just difference is at the the center location there will exist 4 wires on both sets of romexs. Each will have 2 sets of travelers, so the onetime switch will accept 5 wires attached (2 reds and ii Blackness) and a footing.

The simply 2 things you demand to do here are:

First, remove your switch and tie both your travel pair of wires through individually, as shown. For case, red to red black to blackness. Unless installing your Caseta switch in this location. If thats the case, even so tie your extra traveler wire through even though information technology is non existence used.

Second, carefully tuck your wires in the box.

Lastly, install your Pico Remote over the old switch box to hibernate the wires and put on your cover plate.

Not-Neutral Caseta Switch Wiring - four Style

Neutral Based Caseta Switch Wiring - 4 Way

Your All Set

Tips

To do advance programming to your wall dimmer, switch, lamp module go to Lutron Caseta ADVANCED Installation Guide PDF.
If you having a hard figuring out which wires are the travelers, utilise an ohmmeter on your voltmeter. Attach the leads to the two wires and go to the other side and touch the wires you believe are the two traveller wires and check for continuity.
Make sure all ability is off so you practice non crusade impairment to yourself, others, or your equipment.

Source: https://reviewdailylife.com/lutron-caseta-wall-dimmer/

Posted by: fordargift.blogspot.com